Cloudlifter: What It Does, the SM7B, and Do You Need One?
The Cloudlifter is a small metal box made by Cloud Microphones that sits between your microphone and your audio interface and adds up to 25 dB of clean gain. It exists for one reason: some microphones are so quiet that a typical home interface cannot turn them up enough without adding hiss.
It is famous mostly because of one microphone, the Shure SM7B, and because of one question on every podcasting and vocal forum:
Do I actually need one?
The honest answer is that it depends on your interface, not on the mic. This guide explains what the Cloudlifter does, which mics need it, how the different models and alternatives compare, and gives you a gain table so you can check your own setup before spending money.
What Does a Cloudlifter Do?
A Cloudlifter is an inline gain booster, also called a mic activator. You plug your mic into it, then run a second XLR cable from the Cloudlifter to your interface. It has no knobs, no switches (on the CL-1) and no lights.
Power: it runs on the 48V phantom power from your interface. Turn phantom power on and the Cloudlifter uses it.
Gain: up to +25 dB, fixed. Your interface's gain knob still sets the final level.
Phantom power to the mic: blocked. The mic itself never sees 48V, which is why it is safe with passive ribbon mics.
Sound: the circuit is a discrete, Class A JFET design meant to be transparent. It does not color the sound the way a tube or transformer preamp does.
Is a Cloudlifter a preamp?
Not really. It is often called a "pre-preamp". Your interface still has the real preamp; the Cloudlifter just hands it a hotter signal, so that preamp can sit in the quiet middle of its range instead of being cranked to the top, where cheap preamps get noisy.
The signal path looks like this:
Mic → Cloudlifter → audio interface → DAW
Which Microphones Need a Cloudlifter?
Only passive, low-output microphones. Two groups:
Dynamic mics with low output: the Shure SM7B is the classic example, along with the Electro-Voice RE20 and the Rode PodMic.
Passive ribbon mics: ribbons have very low output by design, and many classic ribbons cannot take phantom power. Most are also figure 8 mics, picking up from the front and back. Cloud Microphones actually built the Cloudlifter for its own ribbon mics.
Condenser microphones do not need one (see dynamic vs condenser vs ribbon microphones for how the types differ). They already have an active circuit inside and put out a much hotter signal, and the Cloudlifter would block the phantom power a condenser needs to work.
To put the numbers side by side, here is the sensitivity (output) of a few common mics. Lower means quieter.
| Microphone |
Type |
Sensitivity |
Needs a booster? |
| Shure SM7B |
Dynamic |
1.12 mV/Pa (-59 dBV) |
Often |
| Royer R-121 |
Ribbon |
3.9 mV/Pa |
Often on budget interfaces |
| Shure SM58 |
Dynamic |
1.85 mV/Pa |
Sometimes, for quiet speech |
| MXL 990 |
Condenser |
15 mV/Pa |
No |
Does the Shure SM7B Need a Cloudlifter?
The SM7B is the mic that made the Cloudlifter famous. Shure's own figures put its output at -59 dBV, which means it needs roughly 60 dB of gain to reach a healthy recording level for normal speech.
Most budget interfaces offer somewhere between 55 and 62 dB of gain in total. That leaves you two bad options without a booster:
Turn the knob all the way up: the last few dB of a budget preamp are where the hiss lives.
Record too quiet and boost later: raising the clip in your DAW raises the noise floor along with the voice.
A Cloudlifter fixes this by adding 25 dB before the preamp, so you only need about 35 dB from the interface, which most preamps handle cleanly.
It is not always required, though. If you sing or rap loudly right on the mic, you produce far more level than quiet podcast speech, and many interfaces cope fine without help. If your interface has a strong preamp (see the table below), you can skip it entirely.
Do You Need a Cloudlifter? Check Your Interface
This is the part most guides skip. Whether you need a Cloudlifter comes down to how much clean gain your interface has. Here are the maximum mic gain figures for popular interfaces, from each manufacturer's specs.
| Audio interface |
Max mic gain |
SM7B without booster? |
| Focusrite Scarlett 2i2 (4th Gen) |
69 dB |
Yes, with headroom |
| Solid State Logic SSL 2 / SSL 2+ |
62 dB |
Usable, near the top |
| MOTU M2 |
60 dB |
Usable for loud sources, tight for speech |
| Universal Audio Volt 2 (Gen 2) |
60 dB |
Usable for loud sources, tight for speech |
| Audient iD4 (MkII) |
58 dB |
Booster recommended |
| Focusrite Scarlett 2i2 (3rd Gen) |
56 dB |
Booster recommended |
| Universal Audio Volt 2 (Gen 1) |
55 dB |
Booster recommended |
Specs change between hardware revisions, so check the exact model you own.
A quick way to decide
- Find your interface's max gain in its manual or spec page.
- Under about 60 dB: get a Cloudlifter or similar booster if you use an SM7B, RE20 or passive ribbon.
- 60 to 65 dB: test first. Record your voice at your normal distance and loudness. If you need the knob past roughly three quarters and you hear hiss in quiet passages, add a booster.
- Over 65 dB: you probably do not need one.
- Condenser mic: never needed.
Record your vocal over a full song
Once your gain is set, you need something to sing or rap over. Instead of building a beat from an empty session, describe the track you want and the song template generator builds a full DAW project for Ableton, FL Studio, Logic, GarageBand or Reaper, with the arrangement, MIDI and instruments in place. Open it, arm a track and start recording.
Cloudlifter CL-1 vs CL-2 vs CL-Z
Cloud Microphones makes three versions. All three give the same +25 dB of gain.
| Model |
Channels |
Extra controls |
Best for |
| CL-1 |
1 |
None |
One mic: podcasts, vocals, a single ribbon |
| CL-2 |
2 |
None |
Two mics: stereo ribbon pairs, two-person podcasts |
| CL-Z |
1 |
Variable input impedance, high-pass filter, attenuator (+12 dB) |
Studios that want to shape a ribbon or dynamic mic's tone |
The CL-1 is the one most people mean when they say "Cloudlifter". The CL-Z is the interesting one for engineers: changing the input impedance changes how a ribbon or dynamic mic responds, so it doubles as a tone control. Prices change often; the CL-1 has usually sold for roughly $130 to $180 new, with the CL-2 and CL-Z costing more.
Cloudlifter vs FetHead
The Triton Audio FetHead is the Cloudlifter's main rival. It does the same job in a different shape.
|
Cloudlifter CL-1 |
FetHead |
| Gain |
Up to +25 dB |
Up to +27 dB (into a 3 kΩ load) |
| Shape |
Separate box |
Barrel that plugs straight into the mic |
| Cables |
Needs a second XLR cable |
Uses your existing cable |
| Power |
48V phantom |
48V phantom |
| Channels |
1 (CL-2 has 2) |
1 |
| Price |
Usually higher |
Usually lower |
Pick the FetHead if you want something compact and cheaper, and your mic has room for a barrel on its XLR socket.
Pick the Cloudlifter if you want a sturdy box on the floor or desk, need two channels (CL-2), or want the CL-Z's impedance and filter controls.
Note: Triton also sells a FetHead Phantom for condensers, which passes phantom power through. The standard FetHead, like the Cloudlifter, is for dynamic and ribbon mics.
Other Cloudlifter alternatives
sE Electronics Dynamite DM1: plugs straight into the mic like the FetHead, with up to +28 dB of gain.
Radial McBoost: a box like the Cloudlifter with nearly the same spec, plus adjustable impedance.
Shure SM7dB: the SM7B with a booster built in, switchable between +18 dB and +28 dB. It still needs phantom power, but no extra box. If you are buying an SM7B from scratch, compare the price of the SM7dB against an SM7B plus a booster.
A better interface: if your interface is old or low-gain, upgrading it can cost about the same as a booster and fix the problem for every mic you own.
Can You Use a Cloudlifter Live?
Yes. It works on stage the same way it does in the studio, as long as the mixer provides phantom power. It is useful for low-output dynamic vocal mics on mixers with weak preamps.
One caveat: more gain at the mic does not mean more gain before feedback. Feedback depends on how loud the mic is relative to the speakers, not where in the chain the gain comes from. A booster makes the preamp quieter and cleaner, but it will not let you push the monitors any louder.
Getting a Clean Recording Once Your Gain Is Right
A booster solves one problem: noise from a preamp pushed too hard. A few other settings decide how clean the final take sounds.
Record at 24-bit: it gives you so much room below the signal that aiming for peaks around -12 to -6 dBFS is plenty. More on that in audio bit depth and sample rate explained.
Treat the room before buying gear: an SM7B rejects room sound well, but a bare, echoey room still shows up in the recording.
Compress after recording, not instead of gain: compression evens out a vocal, but it also raises the noise floor. Learn how in what is compression in music.
Check your final loudness: before you release, run the bounce through the LUFS meter to see where it lands against streaming targets.
Verdict
Get a Cloudlifter (or a FetHead) if you use an SM7B, RE20, PodMic or passive ribbon mic on an interface with less than about 60 dB of gain, especially for quiet speech or podcasting.
Test first if your interface sits around 60 to 65 dB. Loud vocals may be fine without one.
Skip it if your interface has 65 dB or more of clean gain, or if you use a condenser mic.
FAQ
What does a Cloudlifter do?
It adds up to 25 dB of clean, fixed gain between a low-output microphone and your audio interface, powered by phantom power. That lets your interface's preamp run at a lower, quieter setting.
Do I need a Cloudlifter for the SM7B?
Only if your interface lacks clean gain. The SM7B needs around 60 dB of gain for normal speech. Interfaces with 65 dB or more, like the Scarlett 2i2 4th Gen, can drive it on their own. Interfaces with under 60 dB usually need a booster.
Does a Cloudlifter need phantom power?
Yes. It only works with 48V phantom power turned on at your interface or mixer. It has no battery or power adapter.
Will phantom power damage my ribbon mic through a Cloudlifter?
No. The Cloudlifter uses the phantom power itself and does not pass it on to the mic, which is why it is popular with passive ribbon mics.
Can you use a Cloudlifter with a condenser microphone?
No. Condensers need phantom power to work, and the Cloudlifter blocks it. Condensers are also loud enough not to need extra gain.
Is the FetHead better than the Cloudlifter?
They do the same job. The FetHead is smaller, slightly cheaper and gives up to 27 dB; the Cloudlifter is a separate box with 25 dB and two-channel and tone-shaping versions. Neither sounds noticeably better than the other for most home recording.
Does a Cloudlifter change the sound?
It is designed to be transparent. Any change you hear usually comes from your interface's preamp running in a cleaner part of its range. The CL-Z's impedance control is the exception: it is meant to change the tone of the mic.
Can I use two Cloudlifters in a row?
You can, but it is rarely useful. 25 dB is enough for almost any passive mic, and stacking boosters adds noise without solving a real problem.